Images are representations only.
HCSHART HART Concentrator System RTU Converter
Brand: Yokogawa Electric CorporationThe HCS HART Concentrator System converts a HART digital signal to a serial (RS-485 or RS-232) MODBUS RTU communication protocol.
This allows HART transmitters and valves to interface directly with MODBUS-based monitoring and control systems.
Operates in Point-to-Point and Digital Multidrop HART Networks: In point-to-point HART mode, the HCS is set to monitor a single instrument.
All process and diagnostic data carried on the HART data string is converted to MODBUS RTU.
Up to 16 HART Devices Per HCS: In a digital multidrop HART network, up to 16 HART instruments digitally communicate on the same wires.
The HCS can be set to monitor any or all instruments and/or valves within the network.
Only one MODBUS address, and one communication link (such as twisted wire pair), is needed to send the process and diagnostic data from up to 16 HART devices to a MODBUS host.
Features- Works with Every HART Compatible Device
- Monitor Primary and Non Primary Variables
- Monitor HART Instrument Diagnostics
- PC Programmable with Windows Software
Specifications
Approvals & Certifications
- CE
- EMC Directive 89/336/EEC, EN 61326
Communication
- Baud Rate: 300 to 19,200 bit/sec
- Data Length: 8-bits - Character Format
- HART
- RS-232 with Modbus RTU Communication Protocol
- RS-485 Modbus RTU Communication Protocol
- Start Bit: 1-bit - Character Format
- Stop Bit: 1-bit - Character Format
Consumption
- 1.5 W, Nominal - Power Consumption
- 2 W at 24 Vdc, Max.
Electrical Connectors
- Terminal Blocks Can Accommodate 14 to 22 AWG Solid Wiring
Humidity
- 0 to 95 % Non-Condensing - Relative Humidity
Indication
- Green LED
- LED
- Red LED
Input
- ± 5 Vdc - Input Over-Range Protection
Input Impedance
- 150 ohms - Transmit Mode
- Less than 5 kiloohms - Receive Mode
Isolation
- 1,000 Vrms between Case, Input, Output & Power Terminals
- 1,500 Vac Dielectric Strength Test for 1 Minute Continuous with No Breakdown
Mounting
- Top Hat DIN Rail Mounting
Operating Temperature
- -40° to 85° C (-40° to 185° F) - for Ambient Conditions
Output Noise
- 100 dB at 50/60 Hz - Common Mode Noise Rejection
Power
- 24 Vdc Loop Power
- 9-30 Vdc ± 10 %
Power Supply
- 23.2 Vdc ± 3 % at 24 mA - Transmitter Power Supply
- 9-30 Vdc
Response Time
- 333 milliseconds in Burst Mode - Digital Response Time
- 50 milliseconds for Data Request - Digital Response Time
- 500 milliseconds in Normal Mode - Digital Response Time
RFI/EMI Effect
- 10 V/m at 80 to 1,000 MHz, 1 kHz AM, when Tested According to IEC 61326 with Error of 0.5 % of Span or Less - RFI/EMI Immunity (Standard)
- 20 V/m at 80 to 1,000 MHz, 1 kHz, when Tested According to IEC 61326 with Error of 0.5 % of Span or Less - RFI/EMI Immunity (with RF Option)
Storage Temperature
- -40° to 85° C (-40° to 185° F) - for Ambient Conditions
Torque
- Tighten Terminals to Four In/Lbs, Max.
Version / Leadwires
- 2-Wire Transmitter
